DIVEGLOSSARY
Recreational diving terms
- Absolute Pressure (ATA)
Total pressure at depth, including atmospheric pressure. At sea level = 1 ATA. Increases by 1 ATA for every 33 ft (salt water) or 34 ft (fresh water) of depth.
Formula: ATA = 1 + (depth / 33). At 33 ft = 2 ATA, at 66 ft = 3 ATA. Used in all gas planning calculations.
ATA = 1 + (depth ÷ 33 ft)- Air
Standard breathing gas — 21% oxygen, 79% nitrogen. The reference gas for all recreational and Navy table calculations.
At depth, the increased partial pressure of nitrogen causes narcosis and nitrogen uptake. Oxygen at elevated partial pressures can cause CNS toxicity if MOD is exceeded (typically not an issue within recreational limits).
- Ascent Rate
The speed at which a diver rises toward the surface. The U.S. Navy and SSI use a maximum of 30 ft/min (9 m/min). PADI sets a maximum of 60 ft/min (18 m/min), and slower is safer.
Ascending too fast prevents nitrogen from off-gassing safely and can cause decompression sickness. Many dive computers alert at 30 ft/min. Technical diving uses 30 ft/min below 50 ft, 10 ft/min above 50 ft.
Max ascent: 30 ft/min below 50 ft · 10 ft/min above 50 ft- Bottom Time (BT)
Total time from leaving the surface to beginning the final ascent. Used with depth to determine pressure group and nitrogen loading.
In repetitive dive planning, BT is used alongside depth to look up the pressure group on Table 1. Actual bottom time cannot exceed the NDL for that depth.
- Buddy System
The practice of always diving with a partner who can assist in an emergency. Fundamental to recreational and technical diving.
A good buddy system includes pre-dive checks, agreed signals, staying within arm’s reach, and a clear plan for separation. Solo diving requires specialized training and equipment.
- BWRAF
Pre-dive buddy check acronym: BCD, Weights, Releases, Air, Final check. Performed before every dive to verify both divers’ gear is correctly configured.
B — BCD inflates/deflates correctly · W — Weights are ditchable and correctly positioned · R — All releases (buckles, clips) are located · A — Air is on, buddy breathes from octopus · F — Final check, nothing trailing or tangled
- Decompression Sickness (DCS)
A condition caused by dissolved nitrogen forming bubbles in the body tissues and blood during or after ascent. Symptoms range from joint pain and fatigue to paralysis or death.
Type I DCS: joint pain, skin rash, fatigue. Type II DCS: neurological, cardiopulmonary, or vestibular symptoms. Treatment is hyperbaric oxygen therapy. Prevention: stay within NDLs, ascend slowly, do safety stops.
Prevention: stay within NDL · ascend ≤30 ft/min · safety stop 3–5 min at 15 ft- EAD (Equivalent Air Depth)
The depth on air that would expose a diver to the same nitrogen partial pressure as a given depth on nitrox. Used to look up NDL from standard air tables when diving nitrox.
EAD = ((1 − FO2) ÷ 0.79) × (depth + 33) − 33- EAN (Enriched Air Nitrox) (EAN / Nitrox)
A breathing gas mixture with more than 21% oxygen — typically EAN32 (32% O2) or EAN36 (36% O2). Increases NDL by reducing the fraction of nitrogen breathed at depth.
More O2 = less N2 = slower nitrogen uptake = longer NDL at the same depth. The tradeoff is a shallower MOD due to higher ppO2. Popular for recreational divers wanting longer bottom times.
- Flying After Diving
The minimum surface interval required before boarding a commercial aircraft to reduce DCS risk from cabin altitude (equivalent to 6,000–8,000 ft above sea level).
DAN/UHMS recommendations: Single no-deco dive = 12 hours · Multiple or multi-day dives = 18 hours · Dives requiring deco stops = >18 hours. Longer is always safer.
- Gauge Pressure
Pressure relative to atmospheric pressure — does not include the 1 ATA of air pressure above the water. A tank gauge reads gauge pressure (e.g. 3000 psi gauge).
Absolute pressure = gauge pressure + 1 ATA. Most practical dive calculations use ATA (absolute), while equipment gauges display gauge pressure.
- Maximum Operating Depth (MOD)
The maximum safe depth for a given gas blend, based on a maximum ppO2 of 1.4 ATA for working dives (1.6 ATA absolute limit). Exceeded MOD risks CNS O2 toxicity.
MOD = ((ppO2 limit ÷ FO2) − 1) × 33 ft EAN32 MOD @ 1.4: 111 ft · EAN36 MOD @ 1.4: 95 ft- Narcosis (Nitrogen Narcosis)
An anesthetic effect caused by nitrogen (and other gases) at depth, producing euphoria, impaired judgment, and slowed reaction time. Often called "rapture of the deep."
Onset typically at depths beyond 100 ft on air. Individual susceptibility varies greatly. Helium does not cause narcosis, which is why trimix replaces some nitrogen with helium for deep dives.
- NDL (No-Decompression Limit)
The maximum time a diver can spend at a given depth without requiring mandatory decompression stops during ascent. Exceeding the NDL means deco stops are required.
NDL decreases with depth: 75 min at 35 ft, 35 min at 60 ft, 22 min at 100 ft (USN Rev 7). Cold or strenuous diving reduces NDL by ~20%. Repetitive dives have shorter adjusted NDLs.
- Off-Gassing
The process of nitrogen leaving the body’s tissues during and after a dive as ambient pressure decreases. The goal of decompression stops and surface intervals.
Off-gassing happens at different rates in different tissues (half-times range from 5 to 635 minutes in Bühlmann models). Fast tissues off-gas quickly; slow tissues hold nitrogen for hours or days.
- On-Gassing
The uptake of nitrogen (or other inert gases) into body tissues during a dive as ambient pressure increases. The process that makes decompression necessary.
- Partial Pressure (pp)
The pressure exerted by a single gas in a mixture. In a gas mix at depth, each component exerts pressure proportional to its fraction of the mix and the total pressure.
ppO2 = FO2 × ATA At 66 ft (3 ATA) on EAN32: ppO2 = 0.32 × 3 = 0.96 ATA- Pressure Group (PG)
A letter (A–Z in PADI or A–Z in USN) that represents a diver’s nitrogen loading after a dive. Used with surface interval time to calculate the adjusted NDL for the next dive.
Group A = lowest nitrogen load. Group Z = highest. After a surface interval, the group letter decreases (nitrogen off-gasses). Group is found on Table 1 by crossing depth with bottom time.
- Residual Nitrogen Time (RNT)
The equivalent bottom time credited to a repetitive diver due to residual nitrogen from a previous dive. Added to actual bottom time to get total bottom time for table lookup.
TBT = RNT + Actual BT Adjusted NDL = NDL − RNT- SAC Rate (Surface Air Consumption)
A measure of how much gas a diver consumes per minute at the surface, expressed in psi/min or cu ft/min. Used to plan gas requirements for any dive.
SAC (psi/min) = (Start PSI − End PSI) ÷ (ATA × Bottom Time) RMV (cu ft/min) = SAC × (Tank Volume ÷ Working Pressure)- Safety Stop
A 3–5 minute pause at 15 ft (5 m) recommended on every dive deeper than 30 ft. Not mandatory but strongly recommended — provides additional off-gassing margin.
Not to be confused with a mandatory decompression stop. A safety stop adds a buffer against DCS even on no-decompression dives. Always do one if you’ve pushed the NDL.
- Surface Interval (SI)
Time spent at the surface between dives. During the SI, nitrogen off-gasses and the pressure group decreases, allowing longer bottom times on subsequent dives.
Minimum SI is 10 minutes for recreational diving. Longer surface intervals = more nitrogen off-gassed = better group letter = more bottom time on the next dive.
- Table Depth (TOD)
At altitude, the depth used for table lookup — always greater than actual depth because reduced atmospheric pressure means more nitrogen is absorbed per foot. Calculated from altitude correction tables.
TOD = Actual Depth × Altitude Factor- Total Bottom Time (TBT)
On a repetitive dive, the sum of Residual Nitrogen Time (RNT) plus actual bottom time. Used to look up the exit pressure group on Table 1.
TBT = RNT + Actual BT- Tank / Cylinder
A high-pressure vessel used to store breathing gas for scuba diving. Common sizes: AL80 (77.4 cu ft), LP85 (85 cu ft), HP100 (100 cu ft).
Aluminum tanks (AL80, AL63) are positively buoyant when empty — require extra weight. Steel tanks (LP85, HP100, HP119) are negatively buoyant. Working pressure varies by tank.
Technical and decompression terms
- Back Gas
The primary gas supply carried on the diver’s back — typically doubles (two tanks manifolded together). Provides the main bottom gas for the entire dive.
Back gas is almost always the travel gas and bottom gas. In a standard tech configuration: doubles of air or trimix for back gas, stages of EAN50 and O2 for decompression.
Rule of thirds: 1/3 out · 1/3 back · 1/3 emergency reserve- Bühlmann ZHL-16
The most widely used decompression algorithm in recreational and technical diving computers. Models nitrogen and helium uptake/elimination across 16 tissue compartments with defined half-times.
Developed by Dr. Albert Bühlmann at the University Hospital Zurich. ZHL-16 forms the basis of virtually all modern dive computer algorithms — including DiveCommand — often modified with gradient factors (GF) for conservatism.
- CNS O2 Toxicity
Central Nervous System oxygen toxicity — caused by breathing high partial pressures of oxygen (ppO2 > 1.4 ATA for extended time). Can cause convulsions underwater with no warning.
CNS % tracks cumulative exposure relative to time limits at each ppO2. Limit is 100% per day. Keep below 80% to leave margin. Convulsions underwater are almost always fatal — strictly enforce MOD.
CNS % = (Time at ppO2 ÷ Time Limit at ppO2) × 100 Daily limit: 100% · Keep below 80% for safety margin- Compartments (Tissue Half-Times)
Mathematical models of body tissues with different rates of nitrogen/helium uptake and elimination. Bühlmann ZHL-16 uses 16 compartments with half-times from 4 to 635 minutes.
Fast compartments (4–10 min) control shallow stops. Slow compartments (200–635 min) control deep stops and long surface intervals. Different algorithms weight compartments differently to generate deco schedules.
- Deco Gas / Decompression Gas
A breathing gas used specifically during decompression stops — typically EAN50 or 100% O2. Higher O2 fraction accelerates off-gassing and shortens decompression time.
EAN50: MOD 70 ft @ 1.4 ATA — used for 30–70 ft stops. 100% O2: MOD 20 ft @ 1.6 ATA — used for 10–20 ft stops. Always verify MOD before switching gases underwater.
EAN50 MOD @ 1.4 ATA: 70 ft 100% O2 MOD @ 1.6 ATA: 20 ft- DIR (Doing It Right)
A diving philosophy emphasizing standardized equipment configuration, team diving, and streamlined gear to maximize safety and redundancy in overhead environments.
Key principles: standardized gas mixes, back gas on manifolded doubles, primary on long hose (7 ft), backup on short hose bungeed to chin, no redundant equipment without purpose, team of 3 minimum for penetration.
- Doubles / Twinset
Two cylinders manifolded together with an isolator valve, providing redundant gas supply. Standard back gas configuration for technical diving. Common configs: 2×LP85, 2×HP100, 2×HP119, 2×HP130.
The isolator manifold allows either post valve or the manifold to be shut independently in case of regulator failure. Provides approximately double the gas volume of a single cylinder at the same working pressure.
- EAN50 (Enriched Air 50%)
A nitrox blend with 50% oxygen, commonly used as a deco gas at 20–70 ft stops. Dramatically accelerates off-gassing compared to air.
MOD at 1.4 ATA = 70 ft. MOD at 1.6 ATA = 56 ft. Must be analyzed before every use. Cylinders must be oxygen-cleaned and labeled.
MOD @ 1.4 ATA = 70 ft · MOD @ 1.6 ATA = 56 ft- END (Equivalent Narcotic Depth)
For trimix dives, the depth on air that would produce the same narcotic effect as the actual depth on the trimix blend. Used to assess narcosis risk.
END = ((1 − FHe) × (depth + 33)) − 33- Exceptional Exposure Deco
A USN Rev 7 decompression classification for dives exceeding standard table limits. Requires in-water oxygen decompression or Surface Decompression with Oxygen (SurDO2).
Marked as "EXCEPTIONAL" in DepthPlanner NavCommand. These dives require a Dive Medical Officer or qualified Diving Supervisor and are not appropriate for recreational or unassisted technical diving.
- Gradient Factors (GF)
A pair of values (GF Lo / GF Hi) used to tune the conservatism of Bühlmann-based deco algorithms. GF Lo controls the depth of the first stop; GF Hi controls the last stop at the surface.
DiveCommand defaults to GF 50/85 in Rec mode and 50/70 in Tech mode, matching the current Shearwater defaults. GF 100/100 = pure Bühlmann (aggressive). Lower Lo = deeper first stop. Higher Hi = less conservative at shallow depth.
GF Lo: controls first stop depth (deeper = more conservative) GF Hi: controls ceiling at surface (lower = more conservative)- Helium (He)
An inert gas used in trimix to replace some nitrogen. Helium is lighter, diffuses faster, and does not cause narcosis — allowing clear thinking at depth.
Helium off-gasses faster than nitrogen (faster half-times), which can complicate decompression if not planned properly. Isobaric counterdiffusion (ICD) can occur when transitioning between helium-rich and nitrogen-rich gases.
- Isobaric Counterdiffusion (ICD)
A phenomenon where helium and nitrogen move in opposite directions across tissue membranes simultaneously, potentially causing bubble formation even without ascent.
Risk occurs when switching from a helium-rich gas to a nitrogen-rich gas at depth. To minimize ICD risk: never increase FN2 by more than 30% at depth during a gas switch.
- M-Values
Maximum Surfacing Values — the maximum inert gas pressure a tissue compartment can sustain at a given ambient pressure without bubble formation, per the Bühlmann model.
Each tissue compartment has its own M-value. When tissue pressure exceeds M-value, decompression is required. Gradient factors are percentages of M-values used to add conservatism.
- OTU (Oxygen Tolerance Unit)
A measure of pulmonary oxygen toxicity exposure over a dive day or repetitive dive series. Different from CNS% — tracks lung/pulmonary oxygen toxicity.
Daily OTU limit = 300 OTUs. Repetitive dive limit = 850 OTUs over multiple days. Generally less of a concern than CNS toxicity for single-day tech dives.
- ppO2 (Partial Pressure of Oxygen)
The pressure exerted by oxygen in a breathing gas at depth. Must be kept below 1.4 ATA for working dives and 1.6 ATA absolute maximum to avoid CNS O2 toxicity.
ppO2 = FO2 × ATA Working limit: 1.4 ATA · Absolute max: 1.6 ATA- RMV (Respiratory Minute Volume)
Gas consumption expressed in cubic feet per minute at the surface. Unlike SAC (psi/min), RMV is tank-independent and directly usable for multi-tank gas planning.
RMV = SAC (psi/min) × (Tank Volume ÷ Working Pressure) Typical tech diver: 0.5–0.7 cu ft/min- Rule of Thirds
The standard gas management rule for open-water technical diving: use 1/3 of your gas going in, 1/3 coming out, and keep 1/3 in reserve for emergencies.
Used for back gas only — stage bottles are planned independently. Turn pressure = fill pressure minus 1/3 of fill pressure. Never penetrate overhead environments without following this rule.
Turn pressure = Fill Pressure × 2/3 Reserve = Fill Pressure × 1/3- Rule of Quarters (Cave)
The most conservative gas rule, used for full cave penetration: use 1/4 going in, turn, use 1/4 coming out, keep 1/2 in reserve. Designed for teams where one diver’s gas must support all.
Turn pressure = Fill × 1/4 Reserve = Fill × 1/2- Sidemount
A configuration where cylinders are carried at the diver’s sides rather than on the back, clipping to D-rings on the harness. Provides excellent redundancy and access to valves.
Each sidemount cylinder is independent — a valve failure affects only one tank. Popular in cave diving (fits through tight restrictions). Gas management treats each tank separately.
- Stage Bottle
An additional cylinder carried alongside the diver (clipped to D-rings) used to extend bottom time or carry decompression gas. Distinguished from back gas by its independent attachment.
Typically AL40, AL50, or AL63 cylinders. Bottom stages carry travel or bottom gas to extend range. Deco stages carry EAN50 or O2 for shallow decompression stops.
- Supersaturation
A state where dissolved inert gas in body tissues exceeds the amount that can remain in solution at ambient pressure. If supersaturation exceeds M-values, bubble formation and DCS can occur.
Controlled supersaturation is how modern decompression works — the body tolerates some supersaturation during staged ascent. Exceeding M-values or GF limits risks symptomatic bubble formation.
- Total Deco Time (TDT)
The sum of all mandatory decompression stop times, not including transit time between stops. A key metric for comparing decompression obligation between dive profiles.
DepthPlanner shows TDT for each dive. TDT > 15 min: O2 deco recommended. TDT > 30 min: O2 deco required per USN Rev 7.
- Travel Gas
A gas used during descent and the initial phase of a dive, before switching to a specific bottom gas. Often used when the bottom gas MOD is shallower than the descent depth.
Example: descending to 200 ft on trimix, using air to 100 ft (travel gas), then switching to trimix at 100 ft. Travel gas must be safe for the shallowest depth it will be breathed.
- Trimix (Tx)
A breathing gas blend of oxygen, helium, and nitrogen. Helium replaces some nitrogen to reduce narcosis and nitrogen loading at depth. Used for dives typically below 130 ft.
Common mixes: Tx21/35 (21% O2, 35% He, 44% N2) for dives to 180 ft · Tx18/45 for deeper. The END tells you the narcotic equivalent depth.
Gas %: O2 + He + N2 = 100% END = ((1 − FHe) × (depth + 33)) − 33- USN Rev 7 Tables
The 7th revision of the U.S. Navy Air Decompression Tables — the standard reference for U.S. Navy diving operations. Provides NDLs and decompression schedules for air diving from 35 to 190 ft.
Used in DepthPlanner NavCommand and IncCommand. Tables include stop depths at 50/40/30/20/10 ft. Exceptional exposure entries require in-water O2 or SurDO2. Updated from Rev 6 with extended NDLs at some depths.